|
Customer feedback : We have
been asked to protect windows by a
facade contractor who is going to be
spraying the above product onto the
surface of finished concrete.
They wish to protect the windows
from splashes of this coating and I
would like you to check whether this
Clearglaze coating would have any
effect on dry film of Windocoat
4930. I am also supplying a sample
for them to test in conjunction with
the coating.Product data sheet for
the Clearglaze attached.
Answer : Robert, The overspray,
should not damage Windocoat 4930.
The clear concrete coating sounds
like an acrylic resin cut in Ketone
and aromatic solvents. The clearcoat
is quite fast in evaporation at 25C.
We are talking about overspray for
direct spray on your Glaze can do
damage. In other words, short
evaporation times of solvent based
coatings, under 2 minutes, will not
damage your Glaze, but prolong
solvent penetration over 4 minutes
can cause a problem. 2.Hello, I am
looking for a sprayable or brushable
translucent coating to protect thin
glass greenhouse panels from
breakage and releasing glass shards
and debris into the greenhouse. What
would you recommend ?
Our Recommendations : Windocoat
4580 is a water based peelable
coating that can be applied to
interior or exterior glass by
airless spray, roller or brush. The
coating cures by water evaporation
and goes from white to clear. Cured,
clear film is water resistant and is
easy to peel from glass. B. Hello Mr.
Goh and thank you for your inquiry.
Our WindOcoat line of temporary
protective peelable coatings are non
hazardous, water based coatings
designed to protect glass, aluminum,
and other non porous surfaces during
transportation and installation in
addition to the potential damage
throughout the construction process.
These coatings are resistant to
paint, concrete splatter, scratch
and minor impact damage. They can be
used indoors and out and can remain
pliable and peelable for extended
periods of time.
These coatings are applied via
airless sprayer, roller, or brush.
When no longer needed they can be
peeled in a sheet or power washed
off and discarded with no
environmental impact. They contain
no VOC’s and are biodegradable.
One gallon will cover approximately
20 to 22 square meters. We do offer
discounts based upon volume. I have
attached a link to our WindOcoat
product page as well as a link to
all our construction related
products. There are videos
demonstrating application and
removal at these links. Hi Mr Goh,
Pls refer to attached photos.
1. On 20/12/09 - Applied windocoat
on glass and put in open unsheltered
area subject to weather condition
2. On 23/12/09 - Applied grade 35
concrete stain and put in open
unsheltered area subject to weather
condition
3. On 31/12/09 – Windocoat easily
peeled off from glass surface. The
glass surface condition looks good.
4. Another sample is still put under
open unsheltered area subject to
weather condition and will arrange
to peel off on 14/1/2010.
Conclusion: 1. Windocoat has no
problem for concrete stain up to a
week old. 2. Shall test for 3 weeks
old concrete stain.Regards, HS Chia
Hi Gene,
The testing carried has been showing
positive results so far.
We would like to place an order for
20,000m2 of glass surface area for
our secured project which will be
installing in March 2010. How much
gallons you reckon we need for the
above mentioned area? Kindly advise
the payment mode and expected
delivery time.
As for the airless spray gun do you
supply the whole kit and how much is
it?Wishing you a Happy New
Year.Warmest Regards EK Goh
Customer Comments : virtually
eliminates window repairs and
reduces clean up costs during
construction and renovation. This
protective coating for windows is
removed in one piece like a big
garbage bag enclosing all trash and
debris revealing a window in
showroom condition! The total cost
adds less than $100 of coating to an
average $175,000 home!
Hi,We're putting together a bid
on a project and your Window coat
4800 (blue) has been specified for
use on the existing windows.We are
located in Milford, Connecticut
c. I am evaluating alternative
protection materials for vertical
and horizontal extruded aluminum and
glass surfaces (curtain wall
systems). Your product looks
promising and I would like
additional information. Your website
indicates the product is best
applied using a sprayer, although it
does depict application with a
roller and mentions use of a brush.
Can the product be successfully
applied using any of these
application methods?
We are looking at protection of
these materials for up to two years
from other trades and foot traffic;
the project is for several
multi-story buildings and an
all-glass bridge. Have you conducted
tests of this product on extruded
aluminum? Has it been tested on
surfaces over a period of time e.g.
2 years for maintenance of
protective properties and ease of
removal? Since these are finished
surfaces, it is imperative that no
residue is left behind from the
protective products.
I am interested in receiving a
sample of this material for in-house
testing. If this is possible, I will
provide you an address for shipment
to our manufacturing facility in
Utah.
This is really an “out of the boxâ€
alternative and I’m hoping I can
include it in my analysis for this
project. c. Hola Walter,
estoy cotizando un edificio que
tiene 1,421m2 de ventaneria, el
cliente necesita una proteccion como
la que me ofreciste para la
instalacion de la ventaneria, este
tema lo dejamos en el tintero desde
julio del 09, mandame una muestra, y
el precio , ademas indicame para
este proyecto cuanto material
necesito, hay que tomar en cuenta
que la ventaneria deberia de salir
pintada de ambas cara del taller,
por lo que seria el doble del area,
mas el grueso, podria si es
necesario mandarte la planilla de
las unidades en autocad.
Ayudame con esto puede ser el
principio. Saludos, Raul Walter,
Windocoat 4880 will cover 190 to 200
square feet. Your account has 2842
square meters. Square meter = 10.764
square feet. You need to cover 30592
square feet. Need a minimum of 3
drums. 165 gallons
|
