|
|
|
|
|
|
|
 |
Introduction:Temporary
Protective Peelable coating for
Helicopter Acrylic Windows,
Aircraft Windshields |
|
|
|
|
|
|
Helicoat 1170 |
|
|
|
|
|
Water based peelable protection for
Helicopter, Temporary Protective
Peelable coating for Helicopter
Acrylic Windows, Aircraft
Windshields |
|
|
|
|
| |
Helicoat 1170 is specifically
formulated for both indoor and
outdoor protection against
scratching and marring of acrylic
windows and windshields during the
handling, transportation, and
storage of rotary and fixed wing
aircraft. It is UV stabilized and
will not crack or discolor for up to
a year outdoors and well beyond
indoors. It remains very pliable and
easy to peel leaving no residue or
effect on the acrylic surface. It is
stabilized against brittleness and
is not softened or penetrated by
most water-based and solvent based
compounds. |
|
|
|
|
| |
Helicoat 1170 is VOC free with water
being the only vapor released during
the curing process. Helicoat is
applied via airless or air assist
sprayer. Helicoat
peelable coating is non flammable
and non combustible as supplied and
when the dry strippable film is
formed and is also low hazard (see
separate Health & Safety Data). |
|
|
|
|
| |
Helicoat 1170 is a CLEAR water
resistant, Peelable temporary
protective that air dries quickly,
leaving a tough, clear flexible
coating that is easily removed from
a variety of surfaces. Helicoat 1170
represents the ultimate in
waterborne removable coating
technology. |
|
|
|
|
|
|
|
| |
 |
Applilcation:Temporary
Protective Peelable coating for
Helicopter Acrylic Windows,
Aircraft Windshields |
|
|
| |
Helicoat 1170 should be used as
received. It can be applied by
airless spray, paint roller, or
brush. The coating dries upon water
evaporation. Wet coating is
milky(white). Dry coating is clear.
Helicoat 1170 should be applied to
form a dry film in the range of 3 to
10 mils(.003" to .010") thick.
Application temperature is ambient
to no lower than 50F. Drying times
will be affected by humidity, film
thickness, air movement and
temperature. Proper fan placement
can speed the dry by removing water
at a much faster rate. Application
by roller might require a few coats.
Thick coating peels in one large
continuous sheet. Thin coatings will
break in areas of coating weakness.
Helicoat 1170 is water based for
safe use and easy water clean up.
Dry coatings are water resistant.
When applying Helicoat 1170 use the
same protection as used while
applying paint. |
|
|
|
|
| |
Note: It is critical
to achieve correct dry film
thickness for removal and peeling. |
|
|
|
|
| |
Application may be Lambs wool Ships
Roller or by spray (conventional air
or airless spray equipment with 21
thou tip size). |
|
|
|
|
| |
Take measures to protect and Mask
areas against overspray. Be
careful and avoid spraying
into small openings where the
coating may become thin and
subsequently difficult to remove.
Must try to Achieve a defined edge
at the end of the area to be coated
by taping the outer edges or by
other methods. Do not apply during
rain or frost. |
|
|
|
|
| |
Equipment: Recommended tip
size for the Airless System is .070,
similar to a glue tip. |
|
|
|
|
|
|
|
| |
 |
Precautions: |
|
|
| |
The surface to be protected with
Helicoat 1170 should be dry, clean
and free from oil, grease and other
water incompatible matter. The clean
surface helps even distribution of
Helicoat 1170. The surface remains
clean when Helicoat 1170 is removed
and surface clean up will not be
necessary for second time
application. |
|
|
|
|
| |
Patch Test: Always test a
small inconspicuous area first.
Because of various substrate
characteristics and conditions like
porosity, deterioration,
embattlement, adverse wear area,
type of ink, paint and or other
coatings applied, abrasion of panted
surfaces, and the like ,it is
difficult to predetermine specific
effects from this product. |
|
|
|
|
|
|
|
|
|
|
| |
 |
Safety & Handling |
|
|
| |
See application and safety
precautions before applying. Liquid
product is slippery when wet. Please
refer to MSDS. |
|
|
|
|
|
|
|
| |
 |
Curing: |
|
|
| |
Helicoat 1170 cures upon water
evaporation. Dry time is dependent
upon temperature, humidity, air
movement and thickness of the
coating. Curing may be accelerated
by forced dry air up to 100 degrees
Fahrenheit. Force dry coatings can
cure in less than 10 minutes. Most
coatings without assist will dry in
a few hours. It is imperative that
Helicoat 1170 be thoroughly cured
and dry, before an attempt is made
to peel the coating from the
substrate. Cured coating is clear
throughout. Cured Helicoat 1170 is
water resistant. Surfaces coated
with Helicoat 1170 can be water
mopped. |
|
|
|
|
|
|
|
|
|
|
|
 |
Storage: |
|
|
| |
Helicoat 1170 should be stored in
the original shipping container with
temperatures between 60 and 90
degrees F. Container should be
sealed until needed. Protection from
freezing is necessary. |
|
|
|
|
|
|
|
| |
 |
Removal: |
|
|
| |
Helicoat 1170 is readily removed
from surfaces by peeling any exposed
edge. This Peelable coating can be
removed by prying an edge and slowly
lifting the coating. |
|
|
|
|
|
|
|
| |
 |
Physical Characteristics: |
|
|
| |
Color: White when wet. Clear
when dry.
Weight: 9.92 Lbs./Gallon
Viscosity: 50-60" on Zahn #2
cup at 77 degrees Fahrenheit
Flashpoint: None |
|
|
|
|
| |
Note: The information
presented herein is our
interpretation of certain test
results and field experience to
date. The information is not to be
taken as warranty or representation
for which we assume legal
responsibility, nor as permission or
recommendation to practice any
patented invention without a
license. It is offered solely for
your consideration, investigation
and verification. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
