|
|
|
|
Protective Peelable coating TubCoat_
For Shower and Bath Tub |
|
|
|
|
| |
Protective Peelable Coating For Shower Stall, Whirl Pool & Bathu Tub |
|
|
|
|
| |
TubProtect 1800 A & 1800 B : |
|
|
|
|
| |
For soft Acrylic Tubs. Protection against damage from the point of manufacture through the residential and commercial installation and construction phase. |
|
|
|
|
| |
Protective Peelable coating For Shower stall ,whirl pool and Bath Tub |
|
|
|
|
| |
TubProtect 1800 is a two component liquid with 100% Solids. It has ZERO VOC. It is fast drying and curing .THE GEL TIME FOR THIS IS ABOUT 8 SECONDS AND THE TACK FREE IS ABOUT 30 SECONDS. YOU CAN WALK ON IN WITHIN A MINUTE under normal conditions with no additional heat or other special curing requirements. |
|
|
|
|
| |
1800 must be applied by spray application. TubProtect 1800 is engineered for use as a temporary protective coating for fiberglass and acrylic bathtub and bath ware fixtures. TubProtect 1800 protects and provides an extremely tough and durable shield against damage during both the transportation and construction process. The elastic rubber-like nature of TubProtect 1800 allows it to absorb minor impacts. 1800 is also very a durable tough coating and thus helps make it very difficult for sharp objects to damage the bath tubs. TubProtect 1800 is also virtually resistant to water and thus eliminates need for plumbing drain test and weather issues.: |
|
|
|
|
| |
Appearance |
Blue Viscous Liquid |
| Product Packaging |
TubProtect 1800 is a 2-component product and is used 1:1 ratio of each component shipped in 55 gallon, Bulk Tote, Tanker |
| Storage |
Store between 50oF. to 100oF. |
| Coating V.O.C. (EPA Method 24) |
0.0 lbs/gal. |
| Storage Life (in closed container) |
6 months |
|
|
|
|
|
| |
Coverage |
1 gallon will cover approx. 110 square feet at the recommended application thickness of 15 mils. .Are these 15 mils dry or wet? This is a 100% solids material (NO SOLVENTS, NO VOC'S). For 15 Mils wet, you get 15 Mills dry film. |
| Spray Application temperature |
Between 35 to 85 f |
| Coating Thickness |
Minimum of 8 Mils |
| Cure Time |
The gel time for 1800 is about 8 Seconds. The tack free time is about 30 seconds. you can walk on in within a minute.
Cure time is affected by the temperature, humidity, and film thickness. Allow the coating to cure for 100 minutes minimum before attempting to remove it. |
| Product Application |
spray equipment such as Plural-Component Proportioning Systems
One such possible equipment supplier is Graco.com In addition, we recommend the GX-8 or Plastic mechanical purge spray guns. |
|
|
|
|
|
|
|
|
|
|
|
| |
 |
Customer Comments: Protective coating For Bathtub, protective mask for bathtub |
|
|
|
|
|
| |
virtually eliminates tub repairs and reduces clean up costs. This protective Peelable coating is removed in one piece like a big garbage bag enclosing all trash and debris revealing a fixture in showroom condition! The total cost adds less than $30 of coating to an average $175,000 home! |
|
|
|
|
| |
TubProtect _-water based Peelable coating that is sprayed onto the Shower stall ,whirl pool and Bath Tub. It dries to form a durable temporary protective Peelable coating that protects the Shower stall ,whirl pool and Bath Tub from damage during the construction phase. |
|
|
|
|
|
|
|
|
|
|
| |
 |
Benefits To You: Protective coating For Bathtub, protective mask for bathtub |
|
|
|
|
|
| |
|
Cost effective solution for Bathtub and Shower fixture damage |
|
Virtually eliminates tub and shower repairs caused during construction. It protects from what the trades dish out |
|
Provides Temporary protection through final inspection |
|
Replaces crude or ineffective liner materials |
|
Value added service for home buyers satisfaction |
|
professional image for contractor and builder |
|
|
|
|
|
| |
TubProtect _ protects tubs, whirlpools and shower stalls against scratches, abrasions and job site dirt and grime. Easy-to-apply, the water-based coating cures to a durable, easy-to-remove "protective skin." One gallon covers approximately two standard 5' tubs |
|
|
|
|
| |
Use for protecting Showers, Bathtubs, Laminates, Polished stone and Non-Porous surfaces. Protects against scratches, nicks, paint overspray, miscellaneous damage, provides reliable protection during the construction process. Peels off easily when the surface is n o longer subjected to construction damage |
|
|
|
|
| |
General Chemical Corp.’s protective Peelable coating TubProtect is a strippable coating engineered for use on a bathtub and wide variety of surfaces. Typical applications include where a temporary protective coating is desired to protect the surface form damage, scratches ,chipping and form exterior and interior environment. Depending on the thickness of the wet film; dry film thickness can range from one to ten mils. Thin films are clear while thicker films are translucent. The application of TubProtect coatings will protect surfaces from paint overspray or damage during manufacturing and shipping. TubProtect represents the ultimate in non-solvent, water borne, strippable coatings. TubProtect does not contain VOCs. |
|
|
|
|
|
|
|
|
|
|
| |
 |
Performance Tests : Protective coating For Bathtub, protective mask for bathtub |
|
|
|
|
|
| |
Place 3 - 5lb Olympic style barbell weights in the tub. (90 degree outside edge - not rounded) Rigidly mount the tub on a random vibration table. Conduct a resonance vibration test using ASTM D 999 Method C in frequency range of 5-300Hz (See Section 9.3.2 for octaves per minute). Passing is 1 hour with no observed damage. Test to simulate shipping damage from plumbing fittings being placed in the tub prior to shipment to job site. |
|
|
|
|
| |
Must stop a 6" drywall knife when dropped on the blade's corner from 8 feet above the tub bottom. Test is to simulate the clumsy dry Waller. |
|
|
|
|
| |
Place a 1 1/4" drywall screw on the tub bottom. Perform ANSI Z124.1 section 4.4 (approximately) directly on top of the screw, Under full load turn the fixture 3 times. There should be no damage from the screw. Test to simulate clumsy drywaller |
|
|
|
|
| |
Protective Peelable coating TubCoat_
For Shower and Bath Tub |
|
|
|
|
| |
Approximate Square Feet Coverage Per Gallon of General Chemical's TubProtect 1800 Peelable coating: Actual Coverage may be slightly lower due to transfer efficiency of spray equipment. |
|
|
|
|
| |
Note: For most applications Minimum of 8 mil of dry coating is needed for peel ability. |
|
|
|
|
| |
TubProtect 1800 |
5 |
8 |
10 |
16 |
18 |
20 |
22 |
25 |
30 |
| Square feet of Coverage per Gallon |
320 |
200 |
160 |
100 |
88 |
80 |
72 |
64 |
53 |
| Dry Film Build Required In Mils |
5 |
8 |
10 |
16 |
18 |
20 |
22 |
25 |
30 |
|
|
|
|
|
|
|
|
|
|
|
| |
 |
Application: |
|
|
|
|
|
| |
1800 must be applied by spray application. spray equipment such as Plural-Component Proportioning Systems One such possible equipment supplier is Graco.com In addition, we recommend the GX-8 or Plastek mechanical purge spray guns. |
|
|
|
|
| |
Guidelines : |
|
|
|
|
| |
Mixing |
Use as received . Do not thin it. |
| Surface Preparation |
Surface must be clean from any soils and oils prior to applying Tubprotect. |
|
|
|
|
|
|
|
|
|
|
|
| |
 |
Removal:Strippable Coating For Bathtubs |
|
|
|
|
|
| |
Coating Film is best peeled or stripped between 45 f to 85 F |
|
|
|
|
|
|
|
|
|
|
| |
 |
Safety & Handling :Floor protection, floor coating and temporary protective coating |
|
|
|
|
|
| |
Avoid breathing vapors/mists that occur during spraying – wear a painter’s mask or other suitable respiratory device when applying this product. Avoid skin and eye contact. Do not allow product to freeze. Keep container closed when not in use. Store in a clean dry area with a minimum temperature of 50ºF. Read Material Safety Data Sheet (Msds )Before use |
|
|
|
|
|
|
|
|
|
|
| |
 |
Flammability: |
|
|
|
|
|
| |
Water Resistant TubProtect presents no fire hazard as received, during, or after application. TubProtect _ is non-flammable in liquid or dry state. |
|
|
|
|
|
|
|
|
|
|
|
 |
Disposal: |
|
|
|
|
|
| |
protective Peelable coating TubProtect is formulated to exclude ingredients that are deleterious to the painting process, such as silicones, or to the water wash system, such as foam generating or foam stabilizing ingredients. |
|
|
|
|
|
|
|
|
|
|
|
 |
Packaging: |
|
|
|
|
|
| |
TubProtect _ is available in 5 gallon,55 gallon & 110 gal/220 gal disposable tote tanks. Totes feature an inner bladder that collapses as product is dispensed, ensuring that all product is usable over the life of the container in service. |
|
|
|
|
| |
Also available in different colors for additional costs. |
|
|
|
|
|
|
|
|
|
|
| |
 |
Operating Guidelines: |
|
|
|
|
|
| |
|
When applying, use the same protection as used while applying paint. The booth ventilation system should be operating while the material is being sprayed. |
|
Chemical goggles and impervious gloves should be worn when handling TubProtect |
|
Do not store or expose below 32F 1800 A. Freezing Temperatures can form crystals and will affect the product performance. freeze thaw by re-heating may not function properly. |
|
Do not expose 1800 A or 1800 B liquid components to any form of moisture. When you vent a product to air, use in line dryer , other moisture removing mechanism and desiccant. |
|
Patch Test Because it is difficult to determine the type of substrate of the Tub such as type of acrylic perform a small test first. This will determine TubProtect effectiveness, coverage, and the approximate amount of time required for it to work |
|
Mask with tape or plastic film before spraying TubProtect 1800 all small, intricate or delicate parts such as whirlpool jets, strainer fittings or window tracks |
|
Before applying TubProtect _, carefully examine the fixture for any pre-existing damage. If damaged, contact the builder or owner before proceeding with installation of the coating. Do not apply to porous surfaces. Do not apply if temperature is below 45ºF. |
|
Coating must be applied of minimum thickness of 8 mils. Too thin coating will not be Peelable. |
|
Overspray of Tubprotect or feather edges can be removed by soaking with a cloth dipped in isopropyl (rubbing) alcohol and then quickly rubbing the area with a dry cloth. |
|
TubProtect is resistant to water, however it is not meant to be water proofing material as water will eventually soften and attack the film. |
|
|
|
|
|
|
|
|
|
|
|
| |
 |
First Time Application: |
|
|
|
|
|
| |
I. Cleaning of equipment: |
|
|
|
|
| |
To clean the pressure pot, airless equipment, spray guns, or spray lines: |
|
|
|
|
| |
|
Flush equipment and lines with the current paint thinner (ex.toluene, xylene, or mek), |
|
Follow with a water reducible solvent, such as butyl cellosolve. This will help to remove any solvent residue. |
|
Thoroughly rinse with water. Making sure that all solvent and paint residues are removed. |
|
|
|
|
|
|
|
|
|
|
|
| |
 |
Testimonials: |
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
