|
Shipprotect
1100 & Shipprotect 1100E:
ShiProtect_1100: For
cold climate
: Application Temperature range
: 35F to 60F
ShiProtect_1100E: For warmer
climate : Application
Temperature range : 60F to 120F
|
|
|
|
|
|
 |
Introduction: |
|
|
|
|
|
|
Shipprotect 1100E is formulated to protect ship or boat decks during construction and storage against minor abrasion and staining. It is weather resistant for several months and will perform over most non-porous surfaces including Glass reinforced Plastics-GRP, non porous wood surfaces and non-skid painted surfaces.
Shipprotect 1100E is water borne temporary protective Peelable
coating formulated for application
in warm to hot climates. |
|
|
|
|
| |
Typical Customer inquiry :We are a yacht refit and repair company operating in Malta, We carry out services such as painting (external and internal), carpentry, teak deck, stainless steel works and many other. Our clients are mainly super yachts. We are a small company however, we intend to grow and actively considering opening a shop in the near future, just off the main yacht marina, thus we actively looking for relative suppliers. |
|
|
|
|
| |
Could you be as kind to forward us some brochures and catalogues regarding your strippable coatings for marine, together with indicative price lists and minimum order quantities. Maybe you can send us a hard copy catalogue together with prices? |
|
|
|
|
| |
Perhaps we can also discuss the possibility of us representing you here in Malta because I as far I could see from your website there is no dealer here in Malta |
|
|
|
|
| |
Shipprotect
1100E peelalbe
coating is non
flammable and
non combustible
as supplied and
has no VOC's |
|
|
| Shipprotect
1100E_
For Temporary Protection of Boat, Yacht
|
|
|
|
|
|
|
| |
Designed especially for
application in warmerclimates.
1100E films are tough and durable to handle heavy forklift and foot traffic. Perfect for floor areas around presses, spray areas, high traffic routes. |
|
|
|
|
| |
It is easy to apply and very easy to peel. Maintenance costs with
1100E are reduced and floors are maintained in brand new condition. .
Shipprotect 1100E has no VOC's |
|
|
|
|
| |
Easily strippable
1100E allows easy maintenance for any Industrial Floors. |
|
|
|
|
| |
Shipprotect 1100E can be used on concrete, tile, glass, ceramic, laminates, brick, and many other non-porous clean surfaces such as : |
|
|
|
|
| |
|
Concrete floors-painted or sealed |
|
Tile Floors-with sealed grout |
|
Wood floors-seal bare wood floors first to prevent pulling up wood fibers |
|
Laminate flooring |
|
Brick Floors-Apply sealant first |
|
Steel, aluminum, brass, copper and other ferrous and non ferrous metals |
|
Glass, plastic and acrylics like Lexan |
|
Other non-porous or well sealed floor materials. |
|
|
|
|
|
| |
General Chemical's
Shipprotect 1100E is a CLEAR water resistant, Peelable temporary protective coating which has many applications. It can be used to protect various types of surfaces during industrial processing.
Shipprotect 1100E air dries quickly, leaving a tough, clear flexible coating that is easily removed from a variety of surfaces.
Shipprotect 1100E represents the ultimate in waterborne removable coating technology. It is stabilized against brittleness and is not softened or penetrated by most water-based compounds. |
|
|
|
|
| |
Shipprotect 1100E is good over cement, linoleum and floor painted with enamels that are resistant to water.
Shipprotect 1100E will adhere to enamels based on emulsions and therefore should not be used. |
|
|
|
|
|
|
|
|
|
|
| |
 |
Benefits To You: |
|
|
|
|
|
| |
Temporary Protective Floor Strippable Coatings and Floor Peelable Coatings For Floors |
|
|
|
|
| |
|
No Flash point Water Based for environment and worker safety |
|
Durable Peelable
coating! |
|
Keeps everything underneath clean
and lifts old dirt up on
old surface giving brand
new look. |
|
|
|
|
|
|
|
|
|
|
|
| |
 |
Application: |
|
|
|
|
|
| |
Shipprotect 1100E should be used as received. It can be applied by airless spray, paint roller, or brush. The coating dries upon water evaporation. Wet coating is milky(white). Dry coating is clear.
Shipprotect 1100E should be applied to form a dry film in the range of 3 to 10 mils(.003" to .010") thick. Application temperature is ambient to no lower than 50ºF. Drying times will be affected by humidity, film thickness, air movement and temperature. Best time to apply is on week-ends or late afternoons to give a coating time to dry. Proper fan placement can speed the dry by removing water at a much faster rate. Application by roller might require a few coats. Thick coating peels in one large continuous sheet. Thin coatings will break in areas of coating weakness.
Shipprotect 1100E is water based for safe use and easy water clean up. Dry coatings are water resistant. When applying
Shipprotect 1100E use the same protection as used while applying paint.. |
|
|
|
|
| |
Note : It is critical to achieve correct dry film thickness for removal and peeling. |
|
|
|
|
| |
Application may be Lambs wool Ships Roller or by spray (conventional air or airless spray equipment with 21 thou tip size). |
|
|
|
|
| |
Take measures to protect and Mask areas against overspray. Be careful and avoid spraying into small openings where the coating may become thin and subsequently difficult to remove. |
|
|
|
|
| |
Must try to Achieve a defined edge at the end of the area to be coated by taping the outer edges or by other methods. |
|
|
|
|
| |
Do not apply during rain or frost. A MINIMUM of two coats of basecoat will be required allowing the first coat to dry before applying the second. |
|
|
|
|
|
|
|
|
|
|
| |
 |
Precautions: |
|
|
|
|
|
| |
The surface to be applied with
Shipprotect 1100E should be dry, clean and free from oil, grease and other water incompatible matter. The clean surface helps even distribution of
Shipprotect 1100E. The surface remains clean when
Shipprotect 1100E is removed and surface clean up will not be necessary for second time application. |
|
|
|
|
| |
Patch Test: |
|
|
|
|
| |
Always test a small inconspicuous area first. Because of various substrate characteristics and conditions like porosity, deterioration, embattlement, adverse wear area, type of ink, paint and or other coatings applied, abrasion of panted surfaces, and the like ,it is difficult to predetermine specific effects from this product. |
|
|
|
|
|
|
|
|
|
|
| |
 |
Safety & Handling: |
|
|
|
|
|
| |
See application and safety precautions before applying. Liquid product is slippery when wet. Please refer to MSDS. |
|
|
|
|
|
|
|
|
|
|
| |
 |
Recommendations: |
|
|
|
|
|
| |
|
outline your floor area to be protected with the self adhesive fiber tape. DO not overlap tap edges ,but keep adjacent |
|
for best results, wet roller with water and squeeze out excess water. For best overall results
1100E should be applied to a minimum of
5 dry mils |
|
apply
Shipprotect 1100E and let it dry. Rinse out roller with plenty of water between coats |
|
Allow first coat to dry. dry time will be affected by coating thickness, application methods, humidity and air flow in the vicinity. Initial drying time is 30 minutes approximately. |
|
Apply second coat and allow it to dry before permitting traffic on the floor. |
|
|
|
|
|
|
|
|
|
|
|
|
 |
Curing: |
|
|
|
|
|
| |
Shipprotect 1100E cures upon water evaporation. Dry time is dependent upon temperature, humidity, air movement and thickness of the coating. Curing may be accelerated by forced dry air up to 100 degrees Fahrenheit. Force dry coatings can cure in less than 10 minutes. Most coatings without assist will dry in a few hours. It is imperative that
Shipprotect 1100E be thoroughly cured and dry, before an attempt is made to peel the coating from the substrate. Cured coating is clear throughout. Cured
Shipprotect 1100E is water resistant. Floors coated with
Shipprotect 1100E can be water mopped. |
|
|
|
|
|
|
|
|
|
|
|
 |
Storage: |
|
|
|
|
|
| |
Shipprotect 1100E should be stored in the original shipping container with temperatures between 60 and 90 degrees F. Container should be sealed until needed. Protection from freezing is necessary. |
|
|
|
|
|
|
|
|
|
|
| |
 |
Removal: |
|
|
|
|
|
| |
1100E is readily removed from surfaces by peeling any exposed edge. This Peelable coating can be removed by prying an edge and slowly lifting the coating off the floor. |
|
|
|
|
|
|
|
|
|
|
| |
 |
Physical Characteristics: |
|
|
|
|
|
| |
Color: White when wet. Clear when dry.
Weight: 9.92 Lbs./Gallon
Viscosity:
Flashpoint: None
|
|
|
|
|
| |
Some Equipment Notes: |
|
|
|
|
| |
Airless System: Recommended tip size is .070, similar to a glue tip. |
|
|
|
|
| |
Note: The information presented herein is our interpretation of certain test results and field experience to date. The information is not to be taken as warranty or representation for which we assume legal responsibility, nor as permission or recommendation to practice any patented invention without a license. It is offered solely for your consideration, investigation and verification. |
|
|
|
|
|
|
|
|
|
|
