|
|
|
| |
 Liquid
Masking Tape For Acrylic
surfaces, Liquid Masking Tape |
|
| |
water based specially designed for
temporary surface protection of
acrylic surfaces such as
Perspex, Lucite, plexiglas and
other acrylic glass .MaskProtect_Acrylic_2630
when applied properly and cured will
peel from acrylic glas cleanly and
esily with virtually leaving no
residue or stain behind. |
|
| |
When Cured: water Resistant, Alkali
resistant and Heat Resistant.
Applications range from interior
protection and exterior
protection of acrylic surfaces . In
specialty applications,
MaskProtect_Acrylic_2630 acts as
barriers to moisture, oxidation,
chemical resistance, and stripper
masks. |
|
| |
|
|
|
|
|
| |
Liquid Masking Tape For Acrylic
surfaces, Liquid Masking Tape
Acrylic glass, polymetyl
methacrylate, PMMA is often used as
a light or shatter-resistant
alternative to glass. It is an
economical alternative to
polycarbonate (PC) when extreme
strength is not necessary. It is
often preferred because of its
moderate properties, easy handling
and processing, and low cost, but
behaves in a brittle manner when
loaded, especially under an impact
force, and is prone to scratching
compared to glass.
MaskProtect_Acrylic_2630 will
help protect against scratching. |
|
|
|
|
|
|
|
| |
 |
Testimonials: |
|
|
|
|
|
| |
This is a potentially huge market
for us, as Perspex is widely used
for many applications, and it
scratches extremely easily…which is
a bonus for us in the protective
products industry. I just need to
find a coating that will work. And
MaskProtect_Acrylic_2630 is just the
product. It works. |
|
|
|
|
| |
Features: |
|
|
|
|
| |
|
Results in a reduction of
labor costs by reducing the
application time. |
|
Once
cured, provides an extremely
tough, uniform film thickness. |
|
Curing time can be cut in half
with the use of increasing
temperatures up to 130ºF. |
|
Easily removed...peels off in
sheets which eliminates messy
hand scrapping. |
|
Safe...non flammable. |
|
Formulated for sag control on
vertical surfaces. |
|
|
|
|
|
|
|
|
|
|
|
| |
Operating Guidelines: How To Apply: |
|
|
|
|
| |
MaskProtect_Acrylic 2630 coating
when applied improperly can cause
problems. Proper application results
in a tough film of uniform thickness
with no sags, less application time
and minimal clean-up labor. |
|
|
|
|
| |
| |
Apply minimum of 10-12
mils wet water based Peelable
film to clean, dry surfaces
(booth walls, fixtures) in a
smooth, continuous spray. If
using airless equipment, use
.015 or .017 nozzle at a set
pressure of 1200-1500 PSI. With
conventional air spray, we
recommend Binks nozzle #68PB
with needle #368 at a pressure
of 35-55 PSI. |
| |
After
significant paint overspray
buildup, film may be quickly and
easily removed. Cut film to
start peeling from one corner. |
| |
Simply peel off in large,
continuous sheets. |
| |
The
coating provides a tough,
flexible solvent-resistant film
which protects walls, paint
fixtures, metal parts in
storage, or any non-porous metal
surface. |
|
|
|
|
|
| |
MaskProtect_Acrylic 2630 is normally
used as received. It is applied by
airless spray, roller or brush . The
sprayed Peelable coating air-dries
in 10 minutes to 3 hours, depending
on thickness of the coating,
humidity, temperature and air
movement. MaskProtect_Acrylic 2630
is applied to form a film thickness
in the range of 5 to 15 mils
(.005" to .015"). The coating is
resistant to attack by most paint
solvents. Application temperature is
ambient to no lower than 60° F.
MaskProtect_Acrylic 2630 coating
cures upon water evaporation.
Improved air movement and
temperatures up to 130ºF will cure
this coating in as little as ten
minutes |
|
|
|
|
| |
To be removed by peeling it
off. |
|
|
|
|
| |
MaskProtect_Acrylic_2630 Peelable
Masking presents no fire hazard
either as received or during or
after application. |
|
| |
 |
Disposal: |
|
|
|
|
|
| |
Follow local , state and federal
regualtions. |
|
|
|
|
|
|
|
|
|
|
|
 |
Some Equipment Notes: |
|
|
|
|
|
| |
Airless System: Recommended
tip size is .070. Similar to a glue
tip will suffice. |
|
|
|
|
| |
Pressure Pot:
MaskProtect_Acrylic works well under
the following conditions.Pot
pressure at 10-15 psi while
atomization pressure is 40 psi. If a
cloud effect occurs the pressure is
too high. try to control this at the
spray gun. If that fails turn down
the pressure a the pressure pot. |
|
|
|
|
| |
MaskProtect_Acrylic2630 can also be
applied by rolling coating or by
brushing. |
|
| |
Note: The information
presented herein is our
interpretation of certain test
results and field experience to
date. The information is not to be
taken as warranty or representation
for which we assume legal
responsibility, nor as permission or
recommendation to practice any
patented invention without a
license. It is offered solely for
your consideration, investigation
and verification |
|
|
|
|
|
|
|
|
|
Top
Liquid Masking Tape For Acrylic
surfaces, Liquid Masking Tape |
|
|
|
